Dispensa-matic
Bottle-Matic II Label Applicator
The perfect machine for labeling your front and back labeled cylindrical containers! Our machines will wrap your bottles, cans, tubes, and jars! The Bottle-Matic is available in three different sizes to save on table space. Label objects from .5" to 10" diameter. By adjusting the front idle roller, this unit will even handle some tapered containers.
This unit is great for short run wine, beer, jellies, jams, sauces, and spice containers.
Even if your can or bottle has ridges we can customize the rollers to work with them. It's simple - just send us your container and a roll of labels, then we'll do the rest. We work with the factory at Dispensamatic to customize your Bottle-Matic. Customizing is based on an hourly charge, but if we can't make it work, you'll pay NOTHING!
Check with us for the correct copy position of the label on the roll so the label will apply in the correct position. Labels should be produced in "Position 3" or "Position 4" for most products. The best position for wine bottles is #3.
 |
New style pressure arm help keep empty containers in place during the labeling process. |
| The roll of labels on a 3" core receive the core guides (2) shown above, then the large roll guides (2), spring washers (2), and thumb screw locking collars (2). The roll of labels is placed on the rod so the label peels off the roll between the two plates and in front of the switch pictured below. |  |
The switches pictured above are assessable from the underside. This stops the feeding when the leading edge of the next label contacts the lever. Minimum gap between the die cut labels for the machine to work is 1/8". The picture on the right shows the modified rollers with groves to allow for lips, caps, or buldges in your container.
 |
After loading the operator selects either single label or double labels. |  |
Minimum/Starting spacing between labels is .5". |
||
| If double labels are selected for front and back application, the operator for gaps over 1/2" uses the following formula. Take the total circumference of the bottle less the total width of both labels, divide by half, and set the dial to the results. Test a bottle and check accuracy. If the gaps between the labels are not even, adjust the switch up or down and test again. The lever on the side of the dial locks in the position of the knob to maintain the setting. The switch on the left is the main power switch. The manufacturer recommend running the unit for 15 minutes before production starts to fully warm up the unit. | ||
 |
Once the label adjustment is found, the operator places the container to be labeled against the stop guide. |  |
| The Bottlematic II is operated when the operator presses the foot switch. | ||
| Item Number | Description | Base Price | |
|---|---|---|---|
| 135M-BM16 | Bottle-Matic 16" Single Sided Label Dispenser up to 15 1/2" | $1,675.00* |  |
| 135M-BM10 | Bottle-Matic 10" Single Sided Label Dispenser up to 9 1/2" | $1,595.00* | |
| 135M-BM6 | Bottle-Matic 6" Single Sided Label Dispenser up to 5 1/2" | $1,525.00* | |
| 135M-BMII16 | Bottle-Matic II 16" Two Sided Label Dispenser up to 15 1/2" | $1,995.00* | |
| 135M-BMII10 | Bottle-Matic II 10" Two Sided Label Dispenser up to 9 1/2" | $1,924.00* | |
| 135M-BMII6 | Bottle-Matic II 6" Two Sided Label Dispenser up to 5 1/2" | $1,849.00* | |
| 135A-BMR4 | BMR4 Optional Rewinder 4" | $375.00 | |
| 135A-BMR6 | BMR6 Optional Rewinder 6" | $375.00 |
Support: Old style microswitch Adjustment
 |
The Optional Rewinder for the BottleMatic makes the job of keeping up with the label liner waste easy. Available in either a 4" or 6" width. The rewinder must be ordered at the time you order the machine. |
Dispensamatic includes a DVD with each dispenser to explain the set up for the BottleMatic II. We highly recommend reviewing the DVD and using it as a training tool for all your operators. The guide above is only for informative purposes for potential customers to review for purchase decisions. If you have a roll of labels available and 6-12 containers, send them to our location listed on our order page and we will set up a machine and video a demo for your review. If you have a Skype (www.skype.com) account we will set up our camera for a live demo.
Made in USA
NAFTA Certificate available.