Take-A-Label
TAL-250E and TAL-450PE
PARTS LIST
Part No. |
Item No. |
Description |
Part No. |
Item No. |
Description |
||
1 |
25108 |
Main Frame |
15 |
25120 |
Micro Switch Mounting Bkt. |
||
2 |
25109 |
Unwind Shaft/250 |
17 |
76800 |
Gear Motor |
||
2 |
45125 |
Unwind Shaft/450 |
18 |
45217 |
Power Cord |
||
3 |
45136 |
Unwind Disc |
19 |
45153 |
Power Cord Clamp (Not Shown) |
||
4 |
72618 |
Unwind Brake Mtl. |
20 |
45155 |
Fuse Holder |
||
5 |
25112 |
Unwind Washer |
21 |
45157 |
Fuse 3 Amp. (Not Shown) |
||
6 |
25113 |
Unwind Spring |
22 |
81905 |
Photo Cell (Not Shown) |
||
7 |
26001 |
Unwind Collar |
23 |
81906 |
Relay (Not Shown) |
||
8 |
26002 |
Unwind Hub Screw |
24 |
81907 |
Relay Socket (Not Shown) |
||
9 |
25114 |
Waste Wind Shaft/250 |
25 |
25122 |
Foot End Caps |
||
9 |
45129 |
Waste Wind Shaft/450 |
27 |
45180 |
Wing/Nut #10-24 (Not Shown) |
||
10 |
25115 |
Waste Wind Clip/250 |
28 |
45181 |
Carriage Bolt #10-24 (Not Shown) |
||
10 |
45131 |
Waste Wind Clip/450 |
29 |
45182 |
Nylon Washer (Not Shown) |
||
11 |
25116 |
Stripping Plate/250 |
30 |
45183 |
Screw #10-32 x 1/2 (Not Shown) |
||
11 |
45124 |
Stripping Plate/450 |
31 |
45184 |
Nut #10-32 Hex Nylon (Not Shown) |
||
12 |
25117 |
Motor/Control Housing |
32 |
45210 |
Thumb Screw 10-24 x 1/2 (Not Shown) |
||
13 |
25118 |
M/C Housing End Plate |
|||||
14 |
25119 |
On/Off Switch 2007 & Older |
|||||
14 |
40007 |
On/Off Switch 2008 & Newer |
|||||
Operating Instructions:
Note: The TAKE-A-LABEL dispenser is shipped mounted to a base to prevent shifting in the container. Remove the machine from the base.
Always load the TAKE-A-LABEL dispenser with the On-Off Switch (14) in the (OFF) position.
- To load a roll of labels on the TAKE-A-LABEL, loosen the unwind hub screw (8) on the unwind collar (7) and remove the collar, unwind spring and disc of the unwind shaft.
- Place a roll of labels on the unwind shaft so that the beginning of the roll is on the bottom of the web coming off to your right as you face the side of the machine.
- Replace unwind disc, unwind spring and collar on unwind shaft. If using labels on a 3" diameter core, the hub on each disc will fit inside the core and support the roll of labels. If labels are on a 1" core, simply slide disc up snug against the roll of labels. When the disc is in place, tighten unwind hub screw (8) against unwind shaft.
- Thread loose end of labels under and up the front of the stripping plate (11).
- Pull labels over top of stripping plate far enough to reach the waist take-up roll (9).
- Remove the waist wind clip (10), thread label backing paper under clip, and reinsert clip over loose paper.
- Position the photo cell switch by loosening thumb screws (32) and moving assembly to right or left so that the photo cell is at or near the center of the labels. The photo cell switch can be tilted forward or backward by loosening the mounting bracket vertical adjustment wing nut (27).
- Turn on On-Off switch (14). The waist wind shaft (9) will turn, winding up backing paper and exposing a label at the top of the stripping plate. When the photo cell sees the dispensed portion of the label, the motor will stop. As each label is removed, the machine will operate until the next label is in position to be removed. (CAUTION:) Turn off switch (14) before removing wound up waist.
- If labels tend to follow backing paper over the top of the stripping plate instead of peeling off, there is probably insufficient tension on the web of the labels. The unwind tension adjustment collar (7) should be moved in to put more tension on the web.
- If the motor stalls it may be necessary to move the tension adjustment collar (7) out to reduce the amount of unwind tension.
