Porous Microcell CLP Coder Ink Roll Uninked

Your Price: $31.80

Part Number: 108C-CLP-MC

Size Printer *

1 1/8" Roller 2" Roller (+$13.95) 3" Roller (+$23.85) 4" Roller (+$34.69)

Quantity

Info
Specifications
FAQ

Un-Inked Microcell CLP Coder Microcell Ink Roll for non porous applications.

For use with the Universal #1150 Coder Inks that are high quality glycol base coder inks formulated for use with our HP-100 and HP-200 series hand printers and all of our fix mount coders for applications requiring printing on corrugated cartons, paper and other porous surfaces. These inks will never dry on metal, plastic or other non-porous surfaces at normal room temperatures.

MC1 fits CLP100 series printers.
MC2 fits CLP200 series printers.
MC3 fits CLP300 series printers.
MC4 fits CLP400 series printers.

Make sure to select the size you need. Price reflects the CLP-MC1 roller.

Pre-Inking Microcell Rolls:

Universal Conveyor Line Printers are shipped from the factory fully assembled and, unless otherwise specified, include a dry Microcell Ink Roll. The ink roll must be manually pre-inked prior to use. Dry ink rolls cannot be properly inked using only the 4 Oz. Reservoir Ink Cartridges. The initial inking of any dry roll is a critical process. The following instructions will guide you through the inking and installation process and have your coder ready to use in a few minutes.

Inks will stain clothing, furniture, carpeting and your hands. Rubber gloves should be worn during the following procedures.

Remove the ink roll from the plastic bag. Fill a clean dry container with enough ink to allow the ink roll to fully submerge. (Microcell Ink Rolls are designed for use with Universal #1150 Ink for marking on porous surfaces. The ink rolls must be pre-inked manually prior to installation on the coder. The 4 Oz. Reservoir Ink Cartridges cannot be used to ink any dry roller.)
Carefully place the ink roll into the ink. Do not force the roll to submerge. The top surface of the roll must remain dry during this process. (The roll should be allowed to float, undisturbed, in the container of ink. Leaving the top surface of the roll dry allows air to escape as the ink is absorbed from the bottom. Forcing the roll under the surface of the ink will prevent the roll from absorbing ink properly.)
As the roll absorbs ink it will begin to sink into the container. When the top surface becomes fully saturated the roll has absorbed as much ink as possible. Using a screwdriver, remove the roll from the container. (This process normally takes 20-25 minutes for a 1-1/8” face roll, longer for the larger rolls. Proper inking of a dry roll is critical to ensure good performance of the roll. When fully saturated, a 1-1/8" face roll will hold approximately 4 ounces (118 ml.) of ink, a 2" face roll will hold approximately 8 ounces (236 ml) of ink, a 3" face roll will hold approximately 12 ounces (354 ml) of ink and a 4" face roll will hold approximately 16 ounces (473 ml) of ink.)
To remove excess ink from the roller, place a round shaft through the core (a screw driver will work nicely) and roll the inked roller across a clean piece of paper or cardboard. (After inking, the roll will be oversaturated with ink. A small volume of ink must be removed or the roller will drip.)

Porous XF Neoprene CLP Coder Ink Roll Dry

$25.80

Select Options

Porous Conveyor Line Printer

$1,295.00

Select Options

Porous Conveyor Line Printer

$595.00

Select Options

Porous Microcell CLP Coder Ink Roll Uninked

Choose Options

Related Items

Porous Microcell CLP Coder Ink Roll Uninked

Choose Options

Related Items

Mailing List